What Size Whole House Water Filter Do I Need

I accept replaced a whole-business firm water-filter sediment cartridge, and it was easier than I thought information technology would be. Here's how I did information technology.

Why Use a Whole Business firm Filtration Organisation?

"OH, CULLIGAN Homo!"

When a home is running off of a safely treated private well or your water has a high mineral and droppings content, you can discover an abundance of minerals, sediment, and even iron in your drinking, bathing, and cooking water that needs to be filtered out. In the past, many people bought a whole-house filtration system and installed it just for this purpose.

We ran across one of these properties and discovered it was well across time to change the sediment cartridge, and then we decided to accept on the challenge. Being our first attempt at such a thing, nosotros took pictures of our take chances. Changing a water-sediment cartridge was a pretty easy task, even for beginning-timers like us; this is how nosotros did it.

Water Filter Cartridge Replacement Guide

Following the written preview of steps ane through 7 listed here, a moving-picture show-by-pic guide will take you through the filter-change process one pace at a time with easy-to-follow directions for each photo. I recommend wearing condom goggles during the projection, as water can spray towards your face, and it may have particles from the captured sediment of the old filter. You will besides desire to place a bucket nether the water-filtration assembly to catch any water every bit it flows out of the housing during the project.

Preview of Projection Steps i–7

Turn off the water supply. Press the red pressure level-relief button. Rotate handle to OFF or Featherbed position.
Unscrew housing. Remove large O-ring, wipe information technology clean, and set bated.
Remove and discard used filter cartridge. Wash housing with dish lather and warm water. Rinse completely. Fill ane/3 with water. Add about 1 tablespoon of bleach and scrub to disinfect. Rinse thoroughly.
Lubricate O-ring with clean silicone grease and insert information technology back into the groove. It is important to make certain the O-ring is seated level in the groove. Otherwise, the housing may not have a proper seal.
Replace the new filter cartridge over the standpipe in the lesser of the housing.
Screw housing onto cap and manus-tighten. Do NOT OVER-TIGHTEN. Make sure cap standpipe slips into cartridge.
Plough on the water supply. Rotate handle slowly to ON position for valve-in-head units. Press the pressure-release button (if present). Bank check for leaks before leaving installation.

Important Information Regarding Your New Filter Change

Later on installing the whole-house sediment-filtration cartridge, run the water!

After you have the filter changed and the housing sealed properly, y'all volition need to run your business firm h2o for almost 5 minutes earlier using any. Information technology is a good thought to run the tap water for drinking and bathing for nearly 30 seconds earlier using information technology for whatsoever consumer purpose. Information technology will be apparent that the water sediments take found their way into the tap organisation, as the initial water that pours from your faucets will probably be a lovely shade of yucky!

Turn Off Water Supply — Plow Off H2o Supply

K9keystrokes

Stride 1: Water Supply Off and Force per unit area Release

Turn off the h2o supply either at the valve-in-caput or main water feed to the filter. Press the ruddy button to release any built-up pressure level, exist careful equally a stream of water comes shooting out when the release push button is engaged.

Note: The red button tin be a groovy practical joke tool to utilize on someone who isn't aware of the thrust of h2o that shoots from the housing pressure-relief valve. Just make sure everyone has safety goggles on!

Step 2: Remove Housing and Clean O-Ring

Unscrew the housing unit and remove the big O-ring. The O-ring is in the housing and looks like a large diameter, but thin blackness safety band. Y'all will need to wipe it clean with a soft cloth and identify it to the side until information technology is fourth dimension to replace it into the housing. Check that it is still in skilful shape, if not, order a new one.

Gyre to Continue

Step 3: Dispose of Sometime Filter and Clean Housing

Remove the muddied old filter and throw it away. Y'all will need to make clean the housing by first rinsing out the bulk of dirt. Then employ dish soap and warm water to launder the housing using a low abrasive sponge or cloth, and so rinse it completely. Fill up the housing 1/3 full with water then add almost a tablespoon of bleach to the housing and scrub gently to sanitize the interior surface. Rinse very thoroughly and several times.

Stride 4: Lubricate O-Ring

Using a clean silicone grease, lubricate the O-ring completely, being certain to embrace the within as well as the outside surface of the o-ring. (It is very of import to utilise a silicone-based grease for this application, as the silicone will not cause the rubber to swell or soften similar a hydrocarbon-based grease volition.) Replace O-band dorsum into its groove. Accept extra care to properly seat the o-band or the seal on the housing will leak, water pressure could dethrone, and your water supply could go vulnerable to leaner.

Footstep 5: Install New Water-Filter Cartridge

At present replace the filter. Look into the housing and you will come across a standpipe positioned at the center bottom. It is a circular-shaped molded component with a short plastic-looking pipe protruding (Encounter photograph #5). Information technology is important to fit the filter over this correctly, as this is the water access port, thus this is where all of your water volition be coming from for filtration before heading to your firm taps. Try to heart the filter on the standpipe.

Pace 6: Screw Housing to Cap

Supervene upon the housing with the filter cartridge by hand-screwing it to the cap. Be sure to get the filter centered over the cap'south standpipe. Yous won't necessarily be able to visually position it just you volition be able to feel the standpipe skid easily into the cartridge opening. Take care NOT to tighten the housing too much, it can crack easily.

Stride 7: Turn on Water Supply and Examination Force per unit area

Slowly rotate the inlet handle to plow the water supply back on. Use circumspection considering the water can come up rushing in besides chop-chop, and this can accident the housing off and destroy the unit. So, turn the inlet valve slowly and experience as the force per unit area arrives so you tin can control it while information technology fills the housing. We replaced a filter with a valve-in-head unit, just the same mensurate of circumspection must be used for any water supply inlet used. Relieve pressure by pressing the cherry-red release push, h2o volition rooster- tail out of the unit of measurement so be prepared to get sprayed a little (or place a towel over the unit while conducting this pace). Make sure you lot have a skilful seal where the housing and cap meet before leaving the unit.

Whole House Water Filter — Whole Firm Water Filter

K9keystrokes

H2o-Filter Cartridge-Replacement Projection Determination

After completing the filter replacement projection, we ran the house water for several minutes. When we starting time opened the faucets, a loud, unfamiliar noise raged from the pipes. It was really startling at first until nosotros realized what the cause was. The water was very dirty looking and spit and sputtered intermittently for some time. Even flushing the toilets and testing the shower offered this experience.

We began to enquire the question, "Now what? Another unexpected projection at this old property?" But then nosotros realized all the knocking and spitting stemmed from the air that had gotten into the pipes during the project. It is a common occurrence and one you should expect to encounter when changing your h2o filter cartridge.

This article is accurate and true to the best of the author's knowledge. Content is for informational or entertainment purposes only and does not substitute for personal counsel or professional advice in business organization, financial, legal, or technical matters.

Republic of india Arnold (writer) from Northern, California on November 30, 2011:

dflood~ Check that the big black safety gasket has been seated correctly, and that you lot have returned the pressure level valves (inlet, outlet) to the correct position. If these exercise non piece of work, you may need to replace your filter housing, or pressure level release button. Expert luck!

dflood on November 29, 2011:

Did all the steps above and now water is coming out of the cherry pressure release push. What did I practice wrong?

India Arnold (author) from Northern, California on September 05, 2011:

Mentum chin~ Give thanks you for the well wishes, you are very sweetness. It pleases me you feel that after reading the instruction for irresolute a whole firm water filter in this hub, that y'all have confidence to do it yourself! I capeesh you swinging by today.

Thanks~

Mentum mentum from Philippines on September 05, 2011:

We have a filtration arrangement installed under our kitchen sink. It looks like to what you have illustrated here. I have never worked on information technology only with your hub guide, I think I tin can do the filter cartridge alter.

Congrats on writing and winning so many plumbing hubs.

India Arnold (writer) from Northern, California on September 03, 2011:

PegCole~ Thank you! I promise you give it a effort yourself if yous always have to change a whole business firm h2o filter. Nosotros found it pretty piece of cake and kinda fun!

Sure appreciate your back up!

HubHugs~

Peg Cole from North Dallas, Texas on September 03, 2011:

Well documented and illustrated. Very thorough and understandable guide to this plumbing task. I experience like I could do this now.

India Arnold (author) from Northern, California on September 02, 2011:

Penny~ Wow, are you right! I have learned and so much past having to do some plumbing things myself; and of course via my dad's luminescence, who has rescued me more than once. Thank you for your supportive comments, I really appreciate it!

Thank you~

SimeyC~ Thank you for the congrats and your kind words. I hope you have been enjoying the plumbing competition, as your winning work has been a wonderful contribution in "how-to"!

Cheers~

Simon Cook from NJ, U.s. on September 02, 2011:

Crawly hub! There goes the bar way high!!! Great stuff - fully deserves the daily prize!

India Arnold (writer) from Northern, California on September 01, 2011:

HRoger~ Hey, Thanks so much for the nice comments and votes! I sure appreciate you stopping by!

Cheers~

HRoger from Online where I can exist! on September 01, 2011:

Hey K9 this is a awesome HUB!

Great data, very creative!

Yous got all my votes:

Useful (one)

Funny (1)

Awesome (one)

Beautiful (i)

Interesting (1)

Take intendance and proceed it up!